Turn any wall switch into an INSTEON switch.
Adding remote control to wired lights or power sockets usually means replacing switches - not any more. With INSTEON's new dual-band Micro On/Off Module, you can keep your antique, toggle or decorative wall switches while adding the power of INSTEON control.
Must be installed by a licensed electrician.
How it works
This compact module installs behind your existing switch, giving it full INSTEON automation while retaining local control at the switch.
Connect the sense wires to any style wall switch to match any type of designer switch theme (antique, push-button, metal, etc.).
Sense wires allow for control via a connected, hard-wired switch. Compatible with standard latching, single momentary and dual momentary switches.
Measuring a tiny 46.6mm square and 17.5mm deep, it can easily be installed above a light fixture in a single-gang electrical box or behind an existing light switch.
INSTEON’s unique dual-mesh technology uses both existing power-lines and wireless radio frequency signals to communicate for best-in-class reliability.
|Name||INSTEON Micro Relay|
|Product Manual||INSTEON Micro Relay (IN2443-522) Product Manual|
|Warranty||24 Months (+ Free 12 month extended warranty)|
|Product Name:||INSTEON Micro Relay (On/Off)|
|Regions:||Australia and New Zealand|
|In the box:||INSTEON Micro Relay (On/Off)|
|INSTEON Powerline Mesh Repeater:||Yes|
|INSTEON RF Mesh Repeater:||Yes|
|Status LED:||Green / On, Red / Off, Blinks green or red during setup, Blinks red to indicate traffic (must be enabled via software)|
|LED brightness:||Adjustable from off to 100% bright|
|Beep on button press:||Beeps red to indicate traffic (must be enabled via software)|
|Commands supported as controller:||On / Off, Fast On / Fast Off, Begin brighten / End brighten, Begin dim / End dim|
|Commands supported as responder:||On / Off, Fast On / Fast Off, Beep|
|RF range:||Up to 50 meters feet open air|
|Phase detect beacon:||Yes|
|X10 addresses:||Any 1 of 256 (unassigned by default)|
|INSTEON device category:||0x02 Switched Lighting Control|
|INSTEON device subcategory:||AUS / NZ (921.0 Mhz), 0x32|
|Mounting:||Behind switch or outlet, or above light fixture in single-gang electrical box||Casing:||UV stabalized plastic (INSTEON White)||Wire connections:||Sense 1 (yellow): 24 AWG, 0.205mm², Sense 2 (purple): 24 AWG, 0.205mm²||Max. wire size:||4mm², 12 AWG (2.72mm diameter)||Min. cable size:||1.5mm², 15 AWG||Screw clamp connections:||Line, Load 1, Load 1 (second terminal), Neutral||Set button:||Yes||Beeper:||Yes||Beep on button press:||Optional (off by default)||LED:||1 RGB|
|Dimensions:||46.6mm W x 17.5mm H x 46.6mm D|
|Operating Conditions:||Indoors, 0° C to 40° C, up to 90% relative humidity|
|Voltage:||100VAC to 240VAC (± 10%)|
|Frequency:||50/60Hz auto-detected at power-up|
|Max. load:||10A, 3600W/240VAC resistive, 700W/240VAC inductive/capacitive, 2000W/240VAC bulbs/low voltage halogen|
|Load types:||Resistive, Inductive/capacitive, Low voltage halogen|
|User replaceable fuse:||N/A|
|Retain all settings without power:||Yes, saved in non-volatile EEPROM|
|Standby power consumption:||<1W|
|Safety approved:||Approved for use in Australia and New Zealand|
|Certifications:||AS/NZS 4268, CISPR 22, IEC 60669-2-1|
Value Quality PerformancePaulon 4/12/2015Installed 6 of these, to find they did not work. Get yourself a plug in relay, will work perfectly then.
Value Quality PerformanceJoeon 5/09/2015All working exactly as they should. Good little product. thanks