Questions about Actiontec MyWirelessTV HDMI AV Sender

<< Back to the product page
 
From Eddie Sorensen on 03/04/2016

Q: can you connect this product to an a/v receiver via the HDMI out?

A: Yes, you can. However you want to make sure that your AV Receiver outputs audio over HDMI (some don't).

(911 votes)


Helpful Helpful Not helpful Not Helpful
From Damien on 21/01/2016

Q: The refresh rate varies each time the tv is turned on with the unit plugged in. This is particularly noticeable during sport. What can be done to optimise this?

A: Using the included silver remote control, please point it at the Receiver unit to access the system settings. Change the "Latency Mode" setting to "Gaming". This should significantly improve the refresh rate. I hope this helps.

(1084 votes)


Helpful Helpful Not helpful Not Helpful
From Keith Warner on 21/12/2015

Q: Can I run two tv screens at once without any loss of picture quality

A: Absolutely you can - up to 3 Receivers can be connected to one Transmitter... so in total, you could actually watch Foxtel on 4 TVs - You can only watch the same channel that is being displayed from your Foxtel box on the main and additional TVs. I hope this helps.

(1112 votes)


Helpful Helpful Not helpful Not Helpful
From Vicky on 10/11/2015

Q: Is it possible to mount the receiver behind the tv such that it is out of site?

A: Yes, both the Transmitter and Receiver units can be wall mounted via the keyhole mounts on the bottom of each unit. The height of each unit is less than 40mm (4cm), so you would need to have at least this amount of clearance behind your TV. I hope this helps.

(1085 votes)


Helpful Helpful Not helpful Not Helpful
From Vicky on 10/11/2015

Q: Does the transmitter need to be connected to a TV?

A: No, this is completely optional. I hope this helps.

(1109 votes)


Helpful Helpful Not helpful Not Helpful
From vooshyp on 14/10/2015

Q: Can you explain the energy saving adapters?

A: The power adapters have been independently ETV (Environmental Technology Verification) verified. You can read more about the ETV program here... http://iet.jrc.ec.europa.eu/etv/about-etv. I hope this helps.

(997 votes)


Helpful Helpful Not helpful Not Helpful
From Vooshyp on 07/10/2015

Q: As the fetch tv stb only has only one hdmi out which is connected to the tv, how does the Actiontec Mywirelesstv connect to the stb?

A: The Actiontec Transmitter has an "HDMI Passthrough" built-in. This means you can plug the Fetch TV directly into the HDMI Input on the Transmitter and then plug one of the included HDMI cables from the HDMI Out on the Transmitter to your TV. I hope this helps.

(945 votes)


Helpful Helpful Not helpful Not Helpful
From Jano on 06/08/2015

Q: Can I connect 2 receivers to 1 sender?

A: Absolutely. You can connect a total of 3 Receivers to a Transmitter.

(1125 votes)


Helpful Helpful Not helpful Not Helpful
From Ken on 08/07/2015

Q: Does the device work with the latest Fetch TV gen 2 STB? Thanks

A: Yes, the Actiontec MyWirelessTV HDMI AV Sender will work perfectly with the Fetch TV Gen. 2 STB. In fact, it will work with any audio visual device that has a standard HDMI output. I hope this helps.

(1140 votes)


Helpful Helpful Not helpful Not Helpful
From Scott on 05/05/2015

Q: Has the box been tested with Foxtel IQ3 and if so, does it work?

A: Yes, this product has been tested and works perfectly with Foxtel IQ3 - including the IR (remote control) return and HDMI passthrough.

(1097 votes)


Helpful Helpful Not helpful Not Helpful

Ask A New Question

* Required Fields