More Views
INSTEON Micro Motor Controller
Details
Add INSTEON control to motorised devices.
Easily add INSTEON control to your motorised window shutters, blinds, projector screens and more. The Micro Motor Controller is the first INSTEON device designed specifically for up/down and open/close motor-controlled appliances.
Must be installed by a licensed electrician.
How it works
This compact module installs behind your existing motor control switch, giving it full INSTEON automation while retaining local control at the switch.
Connect the sense wires to any style wall switch to match any type of designer switch theme (antique, push-button, metal, etc.).
Existing switches
Sense wires allow for control via a connected, hard-wired switch. Compatible with standard latching, single momentary and dual momentary switches.
Compact size
Measuring a tiny 46.6mm square and 17.5mm deep, it can be installed near a motor controlled device in a single-gang electrical box or behind an existing motor control switch.
Dual-Mesh
INSTEON’s unique dual-mesh technology uses both existing power-lines and wireless radio frequency signals to communicate for best-in-class reliability.
Additional Information
Name | INSTEON Micro Motor Controller |
---|---|
Brand | INSTEON |
Model | IN2444-522 |
Product Manual | INSTEON Micro Motor Controller (IN2444-522) Product Manual |
Warranty | 24 Months (+ Free 12 month extended warranty) |
RRP | $89.00 |
General |
|
Product Name: | INSTEON Micro Motor Controller |
Product Code: | 2444-522 |
Regions: | Australia and New Zealand |
In the box: | INSTEON Micro Motor Controller |
Warranty: | 2 Years |
INSTEON |
|
INSTEON Powerline Mesh Repeater: | Yes |
INSTEON RF Mesh Repeater: | Yes |
INSTEON Controller: | Yes |
INSTEON Responder: | Yes |
Maximum links/scenes: | 400 |
Load brightness levels: | 32 locally (256 with software) |
Status LED: | Green / On, Red / Off, Blinks green or red during setup, Blinks red to indicate traffic (must be enabled via software) |
LED brightness: | Adjustable from off to 100% bright |
Beep on button press: | Beeps red to indicate traffic (must be enabled via software) |
Local control: | Yes |
Commands supported as controller: | On / Off, Fast On / Fast Off, Begin brighten / End brighten, Begin dim / End dim |
Commands supported as responder: | Open (On) / Close (Off), Begin raise (brighten) / / Begin lower (dim), End raise (brighten) / End lower (dim), Beep |
Software configurable: | Yes |
RF range: | Up to 50 meters feet open air |
Phase detect beacon: | Yes |
X10 support: | Yes |
X10 addresses: | Any 1 of 256 (unassigned by default) |
INSTEON device category: | 0x0E Window Coverings |
INSTEON device subcategory: | AUS / NZ (921.0 Mhz), 0x32 |
Mechanical |
|
Mounting: | Behind switch or outlet, or above light fixture in single-gang electrical box | Casing: | UV stabalized plastic (INSTEON White) | Wire connections: | Sense 1 (yellow): 24 AWG, 0.205mm², Sense 2 (purple): 24 AWG, 0.205mm² | Max. wire size: | 4mm², 12 AWG (2.72mm diameter) | Min. cable size: | 1.5mm², 15 AWG | Screw clamp connections: | Line, Load 1 (up), Load 2 (down), Neutral | Set button: | Yes | Beeper: | Yes | Beep on button press: | Optional (off by default) | LED: | 1 RGB |
Dimensions: | 46.6mm W x 17.5mm H x 46.6mm D |
Weight: | 72g |
Operating Conditions: | Indoors, 0° C to 40° C, up to 90% relative humidity |
Electrical |
|
Voltage: | 100VAC to 240VAC (± 10%) |
Frequency: | 50/60Hz auto-detected at power-up |
Max. load: | 8A resistive, 3A motor |
Load types: | Resistive, Inductive/capacitive, Low voltage halogen, motor |
Hardwired remote control: | Yes, either latching or momentary switches supported |
User replaceable fuse: | N/A |
Retain all settings without power: | Yes, saved in non-volatile EEPROM |
Standby power consumption: | <1W |
Safety approved: | Approved for use in Australia and New Zealand |
Certifications: | AS/NZS 4268, CISPR 22, IEC 60669-2-1 |