FREE SHIPPING WITHIN AUSTRALIA FOR ALL ORDERS OVER $99

Questions about Z-Wave Automation Bridge

<< Back to the product page
 
From Scott on 12/10/2021

Q: I do not have a Z-wave hub and my entire wifi system is eero mesh. I have Kwikset smart locks whith HomeConnect (Z-wave). Can I use the automation bridge alone to get these Z-wave devices on my HomeKit?

A: The AutomationBridge requires a Z-Wave Hub such as Fibaro Home Center or Vera Edge - it will not work stand-alone with Z-Wave deivces.

(82 votes)


Helpful Helpful Not helpful Not Helpful
From Nir on 26/08/2021

Q: Hello,

I have smart home devices (gateway and switches modules) of Cockpit smart home,https://yourcockpit.biz/.

will this gateway work with this system?

A: I am sorry to say this is not compatible with your hub.

(114 votes)


Helpful Helpful Not helpful Not Helpful
From Marcel Jacobs on 10/08/2020

Q: Will there be more plugins? I would be greatly helped with Yamaha musiccast. And where can I buy the bridge in the Netherlands?

A: Yes, more plugins are being developed all the time. Please check this page for where to buy... https://automationbridge.com.au/?page_id=68

(180 votes)


Helpful Helpful Not helpful Not Helpful
From Tony Tomkins on 31/07/2020

Q: Hi, does it work with home Center 3, thanks

A: Yes, all voice integration work with HC3 (including Apple HomeKit). Some of the additional plugins that are available for AutomationBridge also now work with HC3 - with the balance due for release very shortly.

(168 votes)


Helpful Helpful Not helpful Not Helpful
From Scot Stern on 19/07/2020

Q: Is there any advantage to running a Vera Edge and a Vera Plus at the same time. I would like to buy a Vera Plus but I was thinking that it might be nice to leave my Vera Edge as is and then use the new one with it. Is this possible?

A: The AutomationBridge will only work with one controller - I not believe it is possible to run two Veras and have them act as one system - best to move across completely.

(199 votes)


Helpful Helpful Not helpful Not Helpful
From Adam on 14/07/2020

Q: Will it work with Vera Lite?

A: Yes, it will.

(205 votes)


Helpful Helpful Not helpful Not Helpful
From JOSE on 07/03/2020

Q: I was reading, please correct if I'm wrong... To control Z-wave switch from my iPhone (Apple Homekit) I need Fibaro Home Center and this Bridge??

A: You will need a Z-Wave controller such as the Fibaro Home Center or the Vera controllers (these are cheaper) - and the AutomationBridge.

(276 votes)


Helpful Helpful Not helpful Not Helpful
From Jonathon on 27/01/2020

Q: Hi, will this work with chamberlain garage door opener and Schlage sense deadbolt lock please ? Thx

A: This device is designed to work with Vera and Fibaro Home Center Z-Wave Hubs - it is not a standalone Z-Wave controller.

(316 votes)


Helpful Helpful Not helpful Not Helpful
From Steve on 29/10/2019

Q: Will the automationbridge work with Homey?

A: I am sorry to say it is not compatible with the Homey.

(370 votes)


Helpful Helpful Not helpful Not Helpful
From Terrance on 08/10/2019

Q: Will this connect Ring doorbell and Z-wave Yale Assure lock to homekit so I can lock door with Siri and check front doorbell camera?

A: The AutomationBridge will certainly allow you to add the Yale Z-Wave lock to HomeKit - however I am sorry to say it will not work with the Ring Doorbell (The Ring is a very closed system).

(418 votes)


Helpful Helpful Not helpful Not Helpful

Ask A New Question

* Required Fields