The INSTEON DIN-Rail Relay module clips directly onto a 35mm DIN rail and wires to load, power and neutral. Link it to an INSTEON controller for full remote control over the module and it's connected load. A professional solution for your INSTEON enabled home.
Must be installed by a licensed electrician.
How it works
Clips onto a standard 35mm DIN-rail and provides INSTEON enabled dim/brighten and on/off control of connected lighting.
Connect the sense wires (optional) to any style wall switch to match any type of designer switch theme (antique, push-button, metal, etc.).
Featuring 32 brightness levels (256 levels via the free INSTEON for Hub app), you can easily set the perfect lighting mood for any occasion.
Add a touch-of-class by adjusting the ramp-rate (how quickly your lamp turns on or off) between 0.1 to 5 seconds (0.1 seconds to 8 minutes with app).
DIN-Rail Dimmer module supports connecting multiple lighting fixtures that can then all be controlled by the same wall switch – up to a total of 300W.
Optional sense wires allow for control via a connected, hard-wired switch. Compatible with standard latching, single momentary and dual momentary switches.
As well as brilliant INSTEON control, you can also manually turn your lights on/off or dim/brighten using the convenient toggle button located on the front of the module.
INSTEON’s unique dual-mesh technology uses both existing power-lines and wireless radio frequency signals to communicate for best-in-class reliability.
|Name||INSTEON DIN-Rail Dimmer|
|Product Manual||INSTEON DIN Rail Dimmer (IN2452-522) Product Manual|
|Warranty||24 Months (+ Free 12 month extended warranty)|
|Product Name:||INSTEON DIN-Rail Dimmer|
|Regions:||Australia and New Zealand|
|In the box:||INSTEON Inline Dimmer - DIN|
|INSTEON:||Controller and responder|
|Load brightness levels:||32 locally (256 with software)|
|Status LED:||Green when load is on, red when load is off, Blinks green or red during setup, Blinks red once when responder does not acknowledge/blinks green once if all responders acknowledge (can be disabled via software)|
|LED brightness:||Adjustable from off to 100% bright|
|Local ramp rate:||Adjustable from 0.1 second to 5 seconds locally (0.1 seconds to 8 minutes with software)|
|Commands supported as controller:||On / Off, Fast on / Fast off, Begin brighten / End brighten, Begin dim / End dim|
|Commands supported as responder:||On / Off, Fast on / Fast off, Begin brighten / End brighten, Begin dim / End dim, Incremental brighten / Incremental dim, Beep|
|RF range:||45m +|
|Phase detect beacon:||Yes|
|X10 addresses:||Any 1 of 256 (unassigned by default)|
|INSTEON device category:||0x01 dimmable lighting control|
|INSTEON device subcategory:||2453-222 (921MHz), 0x34|
|Status LED:||Green. Blinks on activation|
|Sense Modes:||Jumper Installed: Open = Group 1 On, Closed = Group 1 Off; Jumper Uninstalled: Open = Group 1 On (or off), Closed = Group 2 On (or Off)|
|Aux. Sensor Input:||Senses contact closure|
|Aux. Sensor Input Wire:||>= 20 gauge wire|
|Setup Memory:||Non-volatile EEPROM|
|Mounting:||35mm (top hat) DIN rail||Max. cable size:||4mm², 12 AWG (2.72mm diameter)|
|Min. cable size:||1.5mm², 15 AWG|
|Screw DIN rail connections:||Line, Neutral, Load, Sense 1, Sense 2||Casing:||UV stabalized plastic (INSTEON White)||Set button:||Yes||Beeper:||Yes||Beep on button press:||Optional (off by default)||LED:||1 RGB|
|Dimensions:||80mm W x 53mm H x 63mm D|
|Operating Conditions:||Indoors, 0° C to 40° F, up to 85% relative humidity|
|Voltage:||100VAC to 240VAC|
|Frequency:||50/60Hz auto-detected at power-up|
|Max. load:||300W at 100-240VAC|
|User replaceable fuse:||Yes (16 A (T)) 5x20mm fuse|
|Retain all settings without power:||Yes, saved in non-volatile EEPROM|
|Standby power consumption:||<1W|
|Certification:||Approved for use in Australia and New Zealand|