2 Wire Magnetic Reed Switch
Reed switches are used to monitor the opening and closing of windows or doors (or essentially anything that opens or closes). There are two parts to a reed switch... one has a magnet inside, the other a reed switch (which is triggered when the magnet comes close and deactivates when the magnet is pulled away). When wired (DIY with 2 low voltage wires) to a smart home binary sensor input device, you can easily monitor and create automations for doors and windows. Can be mounted with double-sided tape or screws.
Aeotec Recessor
Recessor for Fibaro Motion Sensor
Use this Recessor to place Fibaro Motion Sensors within a wall or ceiling allowing them to serve their function more discreetly and preserving the aesthetic appeal of your home. It is easy to install and remove. Simply twist the cover off the Recessor and place your Fibaro Motion Sensor inside, then pull the Recessor clips back as you insert it into the hole in your wall/ceiling.
Aeotec Z-Wave Water Sensor 6 Dock
Designed to compliment the Aeotec Z-Wave Water Sensor 6. With Dock and Water Sensor 6 combined, your home is protected by the most advanced Z-Wave flood sensor available.
Aeotec Z-Wave Plus Range Extender 6
iSmartGate Gate and Garage Roller Door Sensor
Waterproof wireless gate and garage roller door sensor suitable for the iSmartGate Garage Door and Gate Controller. Monitors your garage door or gate status, garage temperature and sensor's battery condition remotely.
iSmartGate Garage Sectional and Tilt Sensor
Waterproof wireless sectional and tilt garage doors sensor suitable for the iSmartGate Garage Door and Gate Controller. Monitors your garage door status, garage temperature and sensor's battery condition remotely.
iSmartGate Wired Gate and Garage Roller Door Sensor
Waterproof wired gate and garage roller door sensor suitable for the iSmartGate Pro Garage Door and Gate Controller.
iSmartGate USB to Ethernet Adaptor
USB to Ethernet Adaptor for a wired connection between your iSmartGate device and your home router or access point. Ideal for locations with too many Wi-Fi devices, where the Wi-Fi signal is not reliable or doesn't reach the desired installation location. This accessory connects to the iSmartGate device using the USB port and to an Ethernet cable (RJ45) using the Ethernet port.
Eve MotionBlinds (1ch or 5ch) Remote Control
Sensibo Pure Replacement Filter
Sensibo Pure Filters are specifically tailored to work seamlessly with Sensibo Pure air purifiers, creating a powerful combination that transforms every room in your living space into a haven of pure, pristine air. Maintain your indoor air quality with Sensibo Pure Filters, the ultimate solution for clean and fresh air. Designed with advanced airflow technology and precision engineering. Sensibo Pure filters should be replaced approximately every six months.
Netatmo Indoor Module for Weather Station
Additional Indoor Module for the Netatmo Personal Weather Station. Place anywhere in your home to monitor temperature, humidity and CO2 readings. You can connect up to 3 Additional Modules to your Netatmo Weather Station.
Netatmo Rain Gauge
By adding the Rain Gauge to your Netatmo Personal Weather Station you will be able to track the amount of rainfall per hour or over a longer stretch (historical data is stored free). You will also be able to set up notification that will notify you when the sensor registers rainfall.
Netatmo Wind Gauge
Designed to work with the Netatmo Personal Weather Station. The first ultrasound wind gauge of its type: the 4 ultrasonic transducers provide ultra-accurate measurements for wind speed and direction.
Netatmo Mount for Rain or Wind Gauge
Mount for Netatmo Rain Gauge and Wind Gauge. The Netatmo mount makes it easier to attach your Rain / Wind Gauge to a wall, roof, pole or railing.
Shelly Bypass
A Shelly Bypass is usually required for both the Shelly 1L and Shelly Dimmer 2 where there is no neutral wire at the wall switch and the power consumption of the attached load is less than 20 watts. In some cases, the Shelly Dimmer 2 may also need this Bypass to stop LED lights "flickering" at low dimming levels for LED lighting with a combined wattage of less then 50W.
Shelly EM Energy Meter 50A or 120A Clamp
Addition energy meter clamps for Shelly EM Energy Meter - available in 50A and 120A ratings.
Shelly Compatible RC Snubber
To be used for all Shelly relays when switching on induction loads such as fans, motors, rollers or equipment that cause voltage spikes during powering on. This Shelly compatible RC Snubber is designed to suppress the voltage spikes caused by the circuit's inductance when a switch, electrical or mechanical, opens. RC snubber should be wired by a licensed electrician between the Output and Neutral of the circuit connected to a Shelly relay.
WARNING: This product MUST be installed by a licensed electrician - additional shielding should be used as required.